J9w66利来官网F

    Current location：Home > Products > 3D Printing Alloy Material > Content

    3D Printing Alloy Material

    Published Date:2020-04-23 23:11:50　Hits:
    Characteristics：

    Good sphericity
    Low oxygen
    High flowability
     
     Cobalt-based Alloy

    technology Grade Composition Wt%
    Co Cr C Mo Ni W Mn Si O
    SLM/EBM CoCrMoW Bal. 26-30 ≤ 0.30 4-6 ≤0.1 4-6 - ≤1 ≤ 0.1
    SLM/EBM CoCrMo Bal. 27-30 ≤ 0.35 4-6 ≤0.5 ≤0.2 ≤1 ≤1 ≤ 0.1
     
    Titanium-based Alloy

    technology Grade Composition   Wt%
    Ti Al V Fe H N C O Other
    SLM/EBM CPT Bal. - - ≤0.3 ≤0.015 ≤0.03 ≤0.08 ≤0.25 ≤ 0.4
    SLM/EBM TC4 Bal. 5-6.75 3.5-4.5 ≤0.4 ≤0.015 ≤0.05 ≤0.08 ≤0.2 ≤ 0.4
    SLM/EBM TC4 ELI Bal. 5-6.5 3.5-4.5 ≤0.25 ≤0.0125 ≤0.03 ≤0.08 ≤0.13 ≤0.4
     
    Nickel-based Alloy

    technology Grade Composition  Wt%
    Ni Cr Mo Nb Fe Ti Al Co Mn Si Cu C O
    SLM/EBM IN625 Bal. 20-23 8-10 3.15-4.15 ≤5 ≤0.4 ≤0.4 ≤1 ≤ 0.5 ≤ 0.5 ≤ 0.07 ≤ 0.1 ≤ 0.1
    SLM/EBM IN718 50-55 17-21 2.8-3.3 4.75-5.5 Bal 0.65-1.15 0.2-0.8 ≤1 ≤ 0.35 ≤ 0.35 ≤ 0.3 ≤ 0.1 ≤ 0.1
     
    Iron-based Alloy

    technology Grade Grade Wt%
    Fe Ni Cr Mo Nb Ti Al Co Mn Si Cu C O
    SLM/EBM 316L Bal. 10-14 16-18 2-3 - - - - ≤ 2 ≤ 1 - ≤ 0.03 ≤ 0.1
    SLM/EBM 304L Bal. 8-12 18-20 - - - - - ≤ 2 ≤ 1 - ≤ 0.03 ≤ 0.1
    SLM/EBM 17-4PH Bal. 3-3.5 15-17.5 - 0.15-0.45 - - - ≤ 1 ≤ 1 3-3.5 ≤ 0.07 ≤ 0.1
    SLM/EBM CX Bal. 8.4-10 11-13 1.1-1.7 - - 1.6-2 - ≤ 0.4 ≤ 0.4 - ≤ 0.05 ≤ 0.1
    DED 431 Bal. 1.5-3.5 17-20 ≤ 1.5 - - - - ≤ 0.5 ≤ 1 - ≤ 0.25 ≤ 0.1
    SLM/EBM 1.2709 Bal. 17-19 ≤ 0.5 4.6-5.2 - 0.6-0.8 0.05-0.15 8.5-9.5 ≤ 0.1 ≤ 1 - ≤ 0.03 ≤ 0.1
     
    PSD： 0-10,  10-30， 15-53， 45-105， 50-150μm

    MORE >>

    Recommended news

    WinXin

    • Sweep code

    Contact Us
    +86 -797-8772869
    Top
    【网站地图】【sitemap】